ZG40Cr25Ni20 (2520) Heat-Resistant Cast Steel Walking Beam For Reheating Furnace

ZG40Cr25Ni20 (2520) Heat-Resistant Cast Steel Walking Beam For Reheating Furnace

What this beam actually does in your furnace The walking beam is not a static refractory support. Every cycle it lifts a full billet or slab load, translates it forward, and sets it down - under furnace atmosphere, at 950–1050 °C, thousands of times per campaign. The failure modes that...
Send Inquiry
Description

bd753a7e99efabca381a1f1948c86847

What this beam actually does in your furnace
 

The walking beam is not a static refractory support. Every cycle it lifts a full billet or slab load, translates it forward, and sets it down - under furnace atmosphere, at 950–1050 °C, thousands of times per campaign.

 

The failure modes that decide your maintenance interval are creep sag, thermal-fatigue cracking at section changes, and oxidation / carburization wall loss. ZG40Cr25Ni20 (2520 / HK40) is the grade specified when those three mechanisms define the replacement cycle.

 
 

Creep Sag

Long-duration load at temperature bows the beam and disturbs billet tracking in the discharge zone.

 
 
 

Thermal-Fatigue Cracking

Repeated stepping cycles crack fillets and section transitions - the classic failure point on cast beams.

 
 
 

Oxidation & Scaling

Cr–Si oxide film slows wall-thickness loss in oxidizing and mild carburizing atmospheres.

 

Verify this against your furnace builder's datasheet

Parameter ZG40Cr25Ni20 (2520) Cross-reference
C 0.35–0.45 % ASTM A297 HK40
Cr 24–26 % DIN 1.4848
Ni 19–21 % GX40CrNiSi25-20
Si 1.5–2.5 % -
Mn/P/S Mn ≤ 1.5; P/S ≤ 0.04 % -
Microstructure Austenitic - no α↔γ transformation Dimensionally stable under cycling
Long-term service 950–1050 °C (some duties to 1100 °C) Short-term peak 1150–1200 °C
  • Third-party inspection (SGS / BV / TPI) and heat-by-heat certificates available on request.

2520 sits at the workhorse position in the 25Cr-20Ni family. It offers well-proven oxidation resistance and thermal-shock tolerance at lower cost than high-Ni/W upgrades (e.g. 2848), and it is the default choice for preheat and heating-zone load-bearing beams, light-to-medium skid rails, and support blocks under cobalt-alloy skid buttons.

 Soaking zone at sustained ≥ 1150 °C with heavy load?

Tell us - we will quote 2848 or another grade with the trade-off stated clearly. We do not push 2520 into a duty it was not designed for.

Performance points that show up in maintenance KPIs
 
 

Not lab adjectives - the mechanisms your maintenance planner can measure.

 

Creep resistance at temperature

The high-carbon austenitic matrix retains structural rigidity under long-duration 950–1050 °C exposure, resisting beam sag and bowing under billet load.

 
 

Thermal fatigue under cyclic stepping

The stepping motion imposes repeated thermal-mechanical cycles. 2520's single-phase structure avoids phase-change dimensional instability and reduces fillet cracking.

 
 

Oxidation & furnace-gas corrosion

The Cr–Si combination forms a protective oxide film that slows scaling and material loss in oxidizing and mild carburizing atmospheres.

 
 

Reproducibility from drawing to part

Precision sand casting or lost-wax casting + solution heat treatment, then CNC machining on mounting faces and interfaces for fit with the furnace support and drive.

 

Walking beams are not catalogue parts

We quote against your drawing, 3D model, or operating-condition parameters. Typical scope of supply:

Moving beam

Fixed beam

Water-cooled beam

Skid beam

Support beam

Tooth-type or plain top profile

Reinforced rib structure

Installation lug bosses

Water-cooled inner channel

Skid buttons / skid blocks

Replacing an imported beam or reverse-engineering an obsolete drawing? Send the original grade and key dimensions - we will confirm the 2520 equivalence and flag any section where a geometry change is advisable for castability or thermal fatigue.

What is checked before the beam ships
 

Chemical composition

Verified per heat against the 2520 specification listed above.

 

Solution heat treatment

Recorded and traceable to the individual part number.

 

Dimensional inspection

Mounting faces, lug bore spacing, and beam straightness - critical for stepping alignment.

 

Visual & surface inspection

Cast surfaces checked; machining marks and foundry marks documented.

 

Third-party inspection

SGS / BV / TPI available on request for EPC and steel-plant QA requirements.

 

Packing & marking

Heat number, part ID, and match-marking for on-site installation sequence.

Frequently Asked Questions
 
 

Is ZG40Cr25Ni20 the same as HK40 and 1.4848?

 

-

Yes for practical procurement purposes. ZG40Cr25Ni20 is the Chinese designation; HK40 is the ASTM A297 grade; 1.4848 / GX40CrNiSi25-20 is the DIN / EN equivalent. Minor Si ranges differ between standards - confirm the Si window on your datasheet if the part goes into a carburizing duty.

Can you supply the beam with skid buttons already fitted?

 

-

Yes. We supply 2520 beams with matching skid buttons / blocks, or with cobalt-alloy buttons where the wear duty requires an upgrade. Buttons can be cast, welded, or mechanically fastened per your drawing.

What drawing information do you need to quote?

 

-

Five items:

(1) overall length and cross-section;

(2) top profile / tooth geometry;

(3) mounting lug positions and bore sizes;

(4) water-cooling channel routing if applicable;

(5) operating temperature and load per beam.

A marked-up PDF or STEP file is sufficient for a first quotation.

What is the typical lead time?

 

-

For a new pattern: pattern-making + casting + heat treatment + machining, typically 6–9 weeks depending on size and quantity. Repeat orders with an existing pattern are shorter.

State your project milestone and we will confirm against foundry capacity.

Do you supply for both new furnace projects and maintenance replacement?

 

-

Both. We work with furnace OEMs and EPC contractors on new walking-beam furnace builds, and with steel-plant maintenance teams on campaign replacement.

For maintenance orders the priority is dimensional match to the existing installed beam - send photos and key measurements if the original drawing is unavailable.

 

 

 

 

 

 

 

Hot Tags: zg40cr25ni20 (2520) heat-resistant cast steel walking beam for reheating furnace, China zg40cr25ni20 (2520) heat-resistant cast steel walking beam for reheating furnace manufacturers, suppliers, factory, 310S Vacuum Furnace Charging Basket, boiler parts, boiler sections, heat resistant steel casting parts, Integrally Cast Annealing Process Furnace Frame, parts in a boiler

Send Inquiry